Laboratoire Travaux Publics, Ingénierie des Transports & Environnement (LTPiTE)
Permanent URI for this community
Browse
Browsing Laboratoire Travaux Publics, Ingénierie des Transports & Environnement (LTPiTE) by Issue Date
Now showing 1 - 11 of 11
Results Per Page
Sort Options
- ItemEffects of the addition of date palm fibers on the physical, rheological and thermal properties of bitumen(Elsevier, 2020) Bellatrache, Youcef; Ziyani, Layella; Dony, Anne; Taki, Mohamed; Haddadi, SmailThis paper investigated the contribution of plant fibers recovered from date palm waste to modify bitumen properties. Palm fibers were characterized to determine their chemical composition, structure, mass loss by heating and tensile strength and the properties of the bitumen-fiber mixtures were evaluated before and after aging using consistency (penetration, Ring and Ball softening point), rheological and thermal tests. The experiments were completed with binder drainage tests on asphalt mixtures to assess the ability for palm fibers to retain bitumen. The results pointed out that the addition of until 6 wt% fibers to neat bitumen conferred a slightly greater consistency, an increase in viscosity by 50% and complex modulus norm by 40% at service life temperatures, before and after aging. These last trends allow to predict the behavior of the asphalt mixtures towards permanent deformations. Thermal analysis on the different mixtures showed that the addition of fibers induced the increase in bitumen crystallinity. The existence of a semi-crystalline fiber network in the bitumen matrix improves the physico-mechanical characteristics of bitumen. The binder drainage tests performed on asphalt mixtures highlighted bitumen absorption by the fibers; this could be correlated to their microstructure and roughness. The results found in this study are encouraging for a potential use of date palm fibers at asphalt mixture scale.
- ItemPlastic bag waste modified bitumen a possible solution to the Algerian road pavements(Taylor & Francis, 2020) Nouali, Mohammed; Derriche, Zohra; Ghorbel, Elhem; Li, ChuanqiangMany Algerian road and highway pavements suffer from severe premature degradations that appear in the first years of their in-service life because of the insufficient performance of the asphalt pavement materials. This study examines the suitability of using plastic bag waste as a bitumen modifier in order to improve the behaviour of asphalt mixes. This paper analyses the effect of adding plastic bag waste; low density polyethylene (LDPE), to a conventional 40/50 graded bitumen. Basic rheological parameters such as penetration, softening point, ageing (RTFOT) and storage stability were used to determine the plastic addition resulting changes on the modified bitumen, expressed relatively to the pure bitumen basis. FTIR spectroscopy was also used to study the chemical functionalities present in the modified bitumen. It was observed that the penetrability of the waste plastic modified bitumen (WPmB) decreases and its softening point increases. Consequently, its thermal susceptibility and its aging rate decrease. Performances of the WPmB were then determined on an asphalt concrete mix (AC) in terms of mix compaction behaviour, stiffness modulus and water resistance ameliorations. Results obtained show that adding plastic waste to the pure bitumen allows reducing void content of the mix and increasing substantially its stiffness modulus and water resistance.
- ItemStrength development and lime consumption progress relationship in lime stabilized bentonite samples(Springer International Publishing, 2021) Gueridi, Fatima; Derriche, ZohraAlthough soil-lime treatment has been successfully used for a long time, the mechanisms behind the clay soil-lime reaction remain insufficiently understood until today. Improvements provoked by lime addition are observed immediately on the soil texture that passes from a plastic state to a coarser state. Strength gain, which corresponds to the advancement of the pozzolanic reaction, develops as a long-time process. Strength development of lime stabilized clays has been extensively studied but investigations on lime consumption progress are scarce. Experimental results related to lime consumption progress, strength development, and pH evolution over time in lime-treated bentonite samples are used in this contribution to shed some light on the clay-lime reaction mechanisms. Results obtained indicate that the short-term and long-term reactions take place sequentially. The short-term reaction occurs at constant pH, lasts about 3 days producing only a limited strength gain. The long-term pozzolanic reaction develops much of the strength gain, which occurs in line with lime consumption and is accompanied by pH value decrease starting from the pH corresponding to the initial consumption of lime (12.65) going down to 11.5 after a long curing time. Based on the results obtained, a strength and lime consumption relationship similar to that that has been shown to exist between strength and the volume of the reaction products formed in cements is defined. XRD results do not show cementing minerals’ peaks but pozzolanic reaction occurrence is evidenced by decrease of the peaks of montmorillonite and silica-based compounds of the studied bentonite.
- ItemStudy of the mechanical and microstructural properties of stone mastic asphalt containing Algerian date palm fibers : influence of the manufacturing process(Springer International Publishing, 2022) Bellatrache, Youcef; Ziyani, Layella; Dony, Anne; Crivelli, Francesca; Shuang, Li; Haddadi, SmailThis study investigated the use of date palm fibers (DPF) extracted from Algerian trees to improve the mechanical performance of wearing courses. For this purpose, fiber-based stone mastic asphalt (SMA) mixtures (0.3 wt% fibers) were prepared by wet and dry processes. Their flow properties, binder drainage, compactability, water sensitivity and rutting resistance were assessed and compared with those of a reference formula (without fibers). Moreover, the tridimensional fiber distribution inside the mixtures was determined using X-ray computed tomography. Marshall test results showed an increase in stability of approximately 23% after fiber addition for both wet and dry fabrication methods. Moreover, gyratory shear compaction experiments demonstrated that the incorporation of fibers resulted in a slight decrease in void content. Owing to the ability of the fibers to absorb bitumen, the wet process was found to be the most effective in reducing the draindown effect (approximately 50%). Moisture susceptibility tests highlighted that palm fibers imply an increase in water sensitivity at 40 °C, probably due to their hydrophilic nature. The introduction of fibers could improve rutting resistance of the mixtures at medium to long-term service life; in particular, using ≤ 1 mm length fibers following the dry process provided the lowest permanent deformation. Macrostructure analyses revealed that palm fibers kept their shape, did not melt in asphalt mixtures and created a 3D networking mechanism without any agglomeration. Therefore, DPF can be promoted in SMA mixtures for the upper layers of asphalt pavements at hot climates.
- ItemNew approach for computing damage parameters evolution in plastic damage model for concrete(Elsevier, 2022) Bakhti, R.; Benahmed, B.; Laib, A.; Alfach, M. T.The Damage Plastic Model is one of the most widespread models used to simulate the real behavior of concrete. The high reliability of this model could be attributed to its ability to take into consideration the elastic stiffness degradation induced by plastic straining as well as the stiffness recovery effects under cyclic loading. This model has been implemented in ABAQUS under the name of Concrete Damaged Plasticity Model (CDPM). Nevertheless, the use of CDPM in ABAQUS is very sensitive due to the high complexity of the calibration process of comparing the model parameters with experimental data, particularly, the stress-inelastic strain diagrams and the damage parameters evolution. The main aim of this research is to develop a new methodology to facilitate the use of this model without the need to calibrate the stress-inelastic strain diagrams and the damage parameters evolution with experimental results. This methodology is based on Lubliner formulas to identify the stress-inelastic strain diagrams, and on Alfarah formulas to evaluate the damage parameters evolution. A new algorithm has been developed to determine the dimensionless coefficients of Lubliner and Alfarah formulas according to the Model Code recommendations. This algorithm has been implemented in developed finite element code where the results have been validated by comparing with experimental results and closed-form solutions.
- ItemNumerical investigation on buried pipelines subjected to permanent ground deformations due to shallow slope failures(Jordan University of Science and Technology, 2023) Bouatia, Mohammed; Demagh, Rafik; Derriche, ZohraPermanent ground deformations (PGDs) induced by slope failures cause catastrophic damage to buried pipelines. This paper presents a 2D plane-strain numerical analysis of the behavior of a 800 mm water transport pipeline buried in the Aine-Tine slope (Mila, Algeria) subjected to shallow PGD, as it could be triggered by the recent earthquake of August 07th, 2020 (M= 4.9). The analysis is carried out through the application of an incremental displacement to simulate the soil-pipeline interaction while focusing on the effect of (1) the magnitude of the PGD and (2) the rigidity of the pipeline on the structural response of the pipeline. The elastic-perfectly Mohr-Coulomb model was used to simulate the soil behavior and the elastic model was used to simulate that of the steel pipe. Pipeline deformations (i.e., translation and ovalization) and radial internal forces’ (i.e., axial forces FA, shear forces FS and bending moments MB) results highlighted that shallow PGD can exert additional loads on pipelines that are proportional to the magnitude of the PGD. It has been found that the soil deformations as well as the internal forces induced on the pipeline ring are higher for rigid pipelines. Moreover, the results indicated that rigid pipelines are more effective than flexible ones as far as ovalization-serviceability limit state is concerned. In effect, for PGD magnitudes of 0.5, 1 and 2 m, the ovalization values of the flexible pipeline are, respectively, higher by 23%, 21% and 18% than those calculated for the rigid pipeline. Through a simplified linear numerical simulation such as that presented in this study, engineers and planners could be guided to foresee the possible causes of pipeline leaks and the mechanisms of ruptures that lead very often to severe disruption of pipelines’ normal operation.
- ItemInvestigation for stress–strain curves of the plastic damage model for concrete(Warsaw University of Life Sciences, 2023) Bakhti, Rachid; Benahmed, Baizid; Laib, AbdelghaniThe Barcelona model is one of the most widespread models used in the nonlinear finite element method for simulating the real behavior of concrete. The strong robustness of this model can be attributed to two main reasons, the first one being its ability to account for the elastic stiffness degradation induced by plastic straining and the second one the aptness of considering the stiffness recovery effects under cyclic loading. This model was examined in the paper by comparing the generated stress–strain diagrams with several analytical solutions from the literature. The comparing process in the compression and tension cases with the closed-form solutions of Desayi, Krätzig, Lubliner and Thorenfeldt proved that the Barcelona model provided identical outcomes with Lubliner’s formula, which was used as the hardening function in the finite element implementation of this model. What is more, this model provided the same curves in case of the others in the ascending branches, and for the descending branch, this study proved that the outcomes of the Barcelona model are completely different from the ones of Desayi in the compression case and slightly similar to Thorenfeldt’s curves in the tension case.
- ItemConsolidation settlement by observational and conventional methods utilizing results of test embankments from Algeria(Jordan University of Science and Technology, 2024) Dali, Mohamed Aymen; Benamghar, Ahcène; Boudjellal, MohamedThe aim of this work is to predict the ultimate primary settlements of a highway embankments using four different methods. These methods include the Terzaghi, Asoaka, Chunlin and hyperbolic methods. Field data from three monitored test embankments in Algeria was used to assess the performance of each method in predicting ultimate primary settlements. Results indicated that the Terzaghi method, relying on laboratory-determined coefficient of consolidation, notably underestimated the intermediate settlement and overestimated the time required to achieve a 90% consolidation in comparison to the other methods. This underscores a significant limitation in solely employing laboratory data. Conversely, the Asaoka, Chunlin and hyperbolic methods, incorporating field measurements, provided more accurate predictions of both settlement and coefficient of consolidation. This study underscores the importance of employing field-based methods to obtain accurate coefficient of consolidation values, thereby enhancing the reliability of consolidation-settlement predictions for the engineering design of highway embankments.
- ItemThe effects of the quality of recycled aggregates on the mechanical properties of roller compacted concrete(MIM Research Group, 2024) Kaabeche, Selma; Belaoura, Mebarek; Kahlouche, RamdaneThis study investigates the performance of roller compacted concrete (RCC) made with recycled aggregates derived from crushed demolished concrete with various proportions of natural. The experimental study examines substituting various proportions of natural aggregate (3/8, 8/15, and 15/20) with recycled aggregate. The replacement rates range from 0% to 100% in increments of 25%. Eleven different mixtures have been made by changing the amount of recycled aggregate used, with and without pre-wetting, before being added to concrete. Additionally, 5% of the cement content was substituted with silica fume and slag in each composition. An experiment test was done to see how recycled aggregate-based BCRs’ performance changed with the incorporation rate on fresh and hardened concrete’s mechanical and physical properties. Physical parameters, including volume masse, vebe time consistency, and mechanical properties such as compression resistance, flexion resistance, and ultrasonic pulse speed, were measured over time. The results found were compared to the control mix made with 100% natural aggregates. Those results show that as the replacement rate increases, the water absorption rate increases with a decrease in mechanical strength. In addition, the pre-wetting treatment did not significantly impact mechanical strength. This can be explained by the characteristics of the recycled aggregate, such as high absorption, low resistance to wear, and low density, which were caused by the residual paste adhered to the recycled aggregate.
- ItemContribution on the dimensioning of a doubly reinforced prestressed concrete I-Beam using GRG and DE optimization(Springer International Publishing, 2025) Bennoui, Imed; Fedghouche, FerhatThis paper presents a comprehensive contribution to the design of doubly reinforced prestressed concrete I-beams by means of cost optimization. The objective function, which is the sum of the costs of the cross-section's constituents (concrete, reinforcement steel, prestressing steel, and formwork), is subjected to design constraints according to Eurocode 2 provisions. These constraints involve serviceability and ultimate limit states, along with current rules of practice, and take into consideration long-term effects such as creep and shrinkage to accurately depict the structural behavior of the I-beam. A combination of gradient-based and metaheuristic optimization techniques is employed to solve the nonlinear optimization problem. An illustrative example demonstrates the efficacy of the optimal design model and its merited gain compared to the conventional design method. The results highlight the significance of certain constraints that are often overlooked in the literature, along with a study of sensitivity to cost fluctuations. An investigation of the results showed that the proposed model can provide practical guidelines for initial geometry selection to achieve more economical conventional designs. Moreover, the model's simple and practical implementation holds potential for extension to other types of prestressed structures.
- ItemBIM-GIS integrated hydrodynamic modeling for road flood risk assessment: a case study in Algeria's Chiffa wadi(Elsevier, 2026) Allalou, Rania; Hebib, Rafik; Bersi, Mohand; Lefkir, AbdelouahabEnsuring the reliability of road infrastructure under extreme flood conditions is critical for resilient transportation systems. This study proposes a hybrid framework integrating Building Information Modelling (BIM), Geographic Information Systems (GIS), and Hydrodynamic Modelling (HDM) to enhance predictive safety assessments for flood-prone transport networks. The framework highlights the concept of Flooded Road Height (FRH) as a reliability metric, which assesses road vulnerability to flooding by comparing flood depth and road elevation. The methodology was applied to Algeria’s Chiffa Wadi, a high-risk gorge environment prone to recurrent flash floods. A comparative analysis was conducted between a Conventional Hydrodynamic Model (C-HDM) and the integrated BIM-HDM framework. Results show that while both models identify the same critical area at PK 65.862, the C-HDM overestimates the flooded road height by over 65 % compared to the BIM-HDM. A quantitative validation against a historical flood event confirmed the superiority of the integrated framework: the BIM-HDM predicted the flood depth with a relative error of 3.8 %, compared to 71 % for the conventional model. This enhanced precision, resulting from the high-fidelity modelling of the infrastructure, enables a more reliable identification of vulnerability root causes and supports the development of targeted resilience strategies. The BIM-HDM framework facilitates the design of structural adaptation solutions through its interoperability with engineering software and the implementation of mitigation systems (early warning) based on a digital twin. While the C-HDM approach remains effective for basic assessments, BIM-HDM offers superior capabilities for predictive risk analysis, which is essential for planning reliable and secure infrastructure.