Développement de Matériaux Innovants (MATINOV)
Permanent URI for this collection
Browse
Recent Submissions
- ItemInvestigation for stress–strain curves of the plastic damage model for concrete(Warsaw University of Life Sciences, 2023) Bakhti, Rachid; Benahmed, Baizid; Laib, AbdelghaniThe Barcelona model is one of the most widespread models used in the nonlinear finite element method for simulating the real behavior of concrete. The strong robustness of this model can be attributed to two main reasons, the first one being its ability to account for the elastic stiffness degradation induced by plastic straining and the second one the aptness of considering the stiffness recovery effects under cyclic loading. This model was examined in the paper by comparing the generated stress–strain diagrams with several analytical solutions from the literature. The comparing process in the compression and tension cases with the closed-form solutions of Desayi, Krätzig, Lubliner and Thorenfeldt proved that the Barcelona model provided identical outcomes with Lubliner’s formula, which was used as the hardening function in the finite element implementation of this model. What is more, this model provided the same curves in case of the others in the ascending branches, and for the descending branch, this study proved that the outcomes of the Barcelona model are completely different from the ones of Desayi in the compression case and slightly similar to Thorenfeldt’s curves in the tension case.
- ItemThe effects of the quality of recycled aggregates on the mechanical properties of roller compacted concrete(MIM Research Group, 2024) Kaabeche, Selma; Belaoura, Mebarek; Kahlouche, RamdaneThis study investigates the performance of roller compacted concrete (RCC) made with recycled aggregates derived from crushed demolished concrete with various proportions of natural. The experimental study examines substituting various proportions of natural aggregate (3/8, 8/15, and 15/20) with recycled aggregate. The replacement rates range from 0% to 100% in increments of 25%. Eleven different mixtures have been made by changing the amount of recycled aggregate used, with and without pre-wetting, before being added to concrete. Additionally, 5% of the cement content was substituted with silica fume and slag in each composition. An experiment test was done to see how recycled aggregate-based BCRs’ performance changed with the incorporation rate on fresh and hardened concrete’s mechanical and physical properties. Physical parameters, including volume masse, vebe time consistency, and mechanical properties such as compression resistance, flexion resistance, and ultrasonic pulse speed, were measured over time. The results found were compared to the control mix made with 100% natural aggregates. Those results show that as the replacement rate increases, the water absorption rate increases with a decrease in mechanical strength. In addition, the pre-wetting treatment did not significantly impact mechanical strength. This can be explained by the characteristics of the recycled aggregate, such as high absorption, low resistance to wear, and low density, which were caused by the residual paste adhered to the recycled aggregate.
- ItemNew approach for computing damage parameters evolution in plastic damage model for concrete(Elsevier, 2022) Bakhti, R.; Benahmed, B.; Laib, A.; Alfach, M. T.The Damage Plastic Model is one of the most widespread models used to simulate the real behavior of concrete. The high reliability of this model could be attributed to its ability to take into consideration the elastic stiffness degradation induced by plastic straining as well as the stiffness recovery effects under cyclic loading. This model has been implemented in ABAQUS under the name of Concrete Damaged Plasticity Model (CDPM). Nevertheless, the use of CDPM in ABAQUS is very sensitive due to the high complexity of the calibration process of comparing the model parameters with experimental data, particularly, the stress-inelastic strain diagrams and the damage parameters evolution. The main aim of this research is to develop a new methodology to facilitate the use of this model without the need to calibrate the stress-inelastic strain diagrams and the damage parameters evolution with experimental results. This methodology is based on Lubliner formulas to identify the stress-inelastic strain diagrams, and on Alfarah formulas to evaluate the damage parameters evolution. A new algorithm has been developed to determine the dimensionless coefficients of Lubliner and Alfarah formulas according to the Model Code recommendations. This algorithm has been implemented in developed finite element code where the results have been validated by comparing with experimental results and closed-form solutions.